1. Adopting the collect dust downside mode, in line with the theory of free fall, the dust collecting effect is good.
3. The system automatically corrects according to the installation position of the product to ensure high-precision cutting requirements.
4. Installed with a static eliminator to remove electricity, dust and air nozzles continue to work, to eliminate static electricity generated when high-speed spindle cutting, to avoid damage caused by static electricity, to avoid the accumulation of dust due to static electricity.
6, The cleaner is equipped with a dust collection box (Maintenance can be arranged according to capacity cutting requirements or dust collection time).
Suitable for split stamp hole PCB board and irregular joint PCB board
Technical Parameters：
Hardware Demand |
YS-300 |
L623*W737*H587mm |
220V/50HZ |
3.6KW |
About 300KG |
Inside / L650*W500*H550mm |
2.2KW/220V |
260mm*260mm |
0-100mm/s |
X, Y axis 0-1000mm/s (min), Z axis 0-750mm/s (min), servo motor drive |
±0.01mm |
X:0-260mm,Y:0-260mm,Z:0-80mm |
0.5-5mm |
0.8-3.0mm |
±0.01mm |
Linear, Circular, U-curve, Arc, L-curve |
Manual, tools needed |
The number of milling cutters (0-5 section) |
none |
controlled by Program |
1pc |
60000rpm |
Air cooling mode |
collect dust downside |
220V ,50HZ |
0.4Mpa |
Safety door and door lock sensor |
offline, load and unload PCBA by hand |
Self-diagnosis,display failure information in real time, query IO state visually, easy for troubleshooting |
IPC, Windows 7 |
USB |
Password protection,the operator enter corresponding interface according to authority to protect important parameters.) |
Visual interface, the cutting point capacity for a single program should be over 400, dynamic simulation of cutting schedule |
Yes |
universal fixture |
≤78 dB(measured in 1M’s distance ) |
1 years |
(Offer service of operation, programming, hardware caring and maintenance training; free upgrade of application. ) |
1. Adopting the collect dust downside mode, in line with the theory of free fall, the dust collecting effect is good.
3. The system automatically corrects according to the installation position of the product to ensure high-precision cutting requirements.
4. Installed with a static eliminator to remove electricity, dust and air nozzles continue to work, to eliminate static electricity generated when high-speed spindle cutting, to avoid damage caused by static electricity, to avoid the accumulation of dust due to static electricity.
6, The cleaner is equipped with a dust collection box (Maintenance can be arranged according to capacity cutting requirements or dust collection time).
Suitable for split stamp hole PCB board and irregular joint PCB board
Technical Parameters：
Hardware Demand |
YS-300 |
L623*W737*H587mm |
220V/50HZ |
3.6KW |
About 300KG |
Inside / L650*W500*H550mm |
2.2KW/220V |
260mm*260mm |
0-100mm/s |
X, Y axis 0-1000mm/s (min), Z axis 0-750mm/s (min), servo motor drive |
±0.01mm |
X:0-260mm,Y:0-260mm,Z:0-80mm |
0.5-5mm |
0.8-3.0mm |
±0.01mm |
Linear, Circular, U-curve, Arc, L-curve |
Manual, tools needed |
The number of milling cutters (0-5 section) |
none |
controlled by Program |
1pc |
60000rpm |
Air cooling mode |
collect dust downside |
220V ,50HZ |
0.4Mpa |
Safety door and door lock sensor |
offline, load and unload PCBA by hand |
Self-diagnosis,display failure information in real time, query IO state visually, easy for troubleshooting |
IPC, Windows 7 |
USB |
Password protection,the operator enter corresponding interface according to authority to protect important parameters.) |
Visual interface, the cutting point capacity for a single program should be over 400, dynamic simulation of cutting schedule |
Yes |
universal fixture |
≤78 dB(measured in 1M’s distance ) |
1 years |
(Offer service of operation, programming, hardware caring and maintenance training; free upgrade of application. ) |
